Red/Green Traffic & Control LightUsed for Traffic Controls in Axle weighing and Over Under Indicators in Check Weighing or On/Off Indicators. Internal A/C Terminal Blocks. Relay Module Needed. Visors, End Cap, 1-1/2” Pipe Thread Adaptor and Bulbs Included
(Consult Factory)

RFID Proximity Readers & Cards 18 Inch Read Range For Outdoor/Indoor Use.
(Consult Factory)

Barcode Scanners and Pin Wands
(Consult Factory)

IDS Radio Frequency RF Modules/Modems Replace cable in new equipment installations as well as retrofitting without costly wiring. Set up equipment where it best serves customers. Upload & download data to your PC. The system can be set up in minutes to enable local-area communication in industrial, commercial and office applications. Provide reliable communication at up to 115.2 Kbps even in RF-hostile environments. Industrial-grade enclosure contains a robust 2.4GHz or 900MHz transceiver. Each communication system requires a central server node and any number of remote client nodes that operate in point-to-point or point-to-multipoint configurations. Users can create multiple sub-networks by assigning unique radio addresses to specific device groups.
(Consult Factory)

Dial up Serial Modem/Data Logger/TTL Control Store up to 16 megabytes of record data at remote sites for periodic retrieval. It can also be used for alarm monitoring and event reporting and is compatible with most telephone systems. Transmits through a standard RS-232 serial port. This data can then be downloaded from a remote location. Contact closures that will trigger a call-in to a service center. Connect to 4 different serial devices from a remote location. Control And Extract Reports From IDS Products Via PC.
(Consult Factory)

Bill Acceptor for Pay & Weigh Systems New Bill Type Acceptor Modules pre-configured to interface to an IDS Instrument. We Have Axle Weighers and various other All-In One & Custom Systems
(Consult Factory)

Junction Box Four Channel, Individual Signal Trim Pots & Load Cell Switches For Diagnostic Testing. Removeable Terminal Blocks. Lightning & Welding Protection.
(Consult Factory)

The Model 8501 External Relay Module in NEMA Enclosure. The 4-Channel Input / Output Relay Module is used for Activating Motors, Solenoids and Switching and Receiving Signal Lines. Bulk-Weighing, Setpoints, Remote Sensing Interlocks, Push Buttons and TTL Outputs. A/C and DC Relays are Available.
(Consult Factory)

The Model 8502 Intrinsic Safety Barriers Enclosed in a NEMA Enclosure. Used in Hazardous Environments with Digital Weight Indicators.
(Consult Factory)

The Radio Frequency Relay Input/Output Modules RF Remote Control Modules are designed for Industrial Applications. Remote Zero, Print, Tare. Execute a Function. Each transmitter is factory programmed with a unique serial number. The receivers learn this serial number and store it in EEPROM, which does not require a backup power system to retain serial number codes. Each receiver can learn up to four different transmitter serial numbers. Special orders can be placed for multiple transmitters with the same serial number if needed. FCC approved, Keychain size, Range: 150ft. typ., Can be used with 2, 4 and 8CH RF receivers PCB size: approx: 1.3"x1.3".
(Consult factory for quote)

The Photoelectric Sensor With Built-In Amplifier Kit Includes: Retro-reflective Photo Sensor, Reflector, Adhesive back reflector sheet, Photo-Sensor provides long sensing distance - 4 m (13.12’). Enclosure rating (IP67 - IEC60529) Switch selectable Light-ON/Dark-ON operation. Optional NEMA Fiberglass Enclosure with Opto-22 Relay & 12-24 VDC Power supply available.
(Consult Factory)

IDS Start Stop/Control Module The IDS Start, Stop, Print, Tare, Zero & Control Module Mounted in NEMA Enclosure with Terminal Block and Liquid Tight Cable Cinch Tights Various Switch Configurations and Sizes Available.
(Consult Factory)

Industrial Data Systems, Inc.
3822 E La Palma Ave, Anaheim CA. 92807
Phone 714-921-1353
                        Outside of CA sales 800-854-3311